Sonoff Mini Pairing Mode

Sonoff Mini Pairing Mode. Let’s set these up to see how they’re supposed to be used. Power off and then on to enter again (the bulb changes from dim to bright repeatedly).

Sonoff pairing come accoppiare Sonoff Mini, Basic, TH16 from lamiacasaelettrica.com

Sonoff mini gets connected in the same way as other devices. Long press (5 sec) the device button => this triggers the quick pairing mode with ewelink ==> blue led blinks: Power off and then on to enter again (the bulb changes from dim to bright repeatedly).

Source: lamiacasaelettrica.com

Power on after powering on, the device will enter the pairing mode during the first use and the led signal indicator flashes. Let’s set these up to see how they’re supposed to be used.

Source: www.sonoff.in

I figured that the firmware on the sonoff needs to be the latest version (3.3 +) before the diy mode password and ssid work. I'm on my 4th & 5th sonoff mini in diy mode.

Source: www.sonoff.in

If the the led pairing indicator blinking as “compatible paring mode (ap)”, it means the device is in compatible paring mode, short press the pairing button one time to quit compatible paring mode, then long press the pairing button for 5 seconds, the device will enter the quick pairing mode which is used for quick pairing approach. Cloud users don't have these problems.

Source: www.sonoff.in

During the pairing stage, i put the receiver into pairing mode (holding down the push button) i can then see the device, however it fails to connect to the device in ewelink. The device will exit the quick pairing mode (touch) if not paired within 3mins.

Source: lamiacasaelettrica.com

The google home app is developed by google to centrally set up, manage and control devices such as google nest, google wifi, and chromecast as well as thousands of compatible smart home products. Connect the mini to your mains outlet (220v or 110v).

Source: lamiacasaelettrica.com

Sonoff minir2 can work in diy mode. Sorry to jump in but looks like you have the issue with the sonoff mini with the fw 3.6 and in diy mode that i'm facing with the sonoff basic r3 with the fw 3.5 and 3.6 also (by the way i have two sonoff mini with the fw 3.3.0 and in diy mode which i don't want to upgrade since i fear that might stop work well).

Source: notenoughtech.com

The mini should immediately start up and go into pairing mode during first time init. Long press (5 sec) the device button => this triggers the quick pairing mode with ewelink ==> blue led blinks:

Source: www.sonoff.in

This video is a beginner's guide to pair sonoff t1 in quick pairing mode. Read more information about zigbee2tasmota in the documentation.

Source: lamiacasaelettrica.com

After that it should be discovered and added into ha automatically. If the device has been previously paired with ewelink app, reset.

Let’s Set These Up To See How They’re Supposed To Be Used.

If the device has been previously paired with ewelink app, reset. After that it should be discovered and added into ha automatically. Connect the mini to your mains outlet (220v or 110v).

Connect The Device Using The Instructions Of Ewelink Application.

I figured that the firmware on the sonoff needs to be the latest version (3.3 +) before the diy mode password and ssid work. Sonoff minir2 can work in diy mode. Is there some other step i need to take that none of these articles are mentioning?

The Process Is Still A Little Bit Clunky, But You Can Enjoy Tasmota On Sonoff Zigbee Bridge.

Cloud users don't have these problems. There are some good guides below that walk you through the process: Try turning it off and on again:

If The Sonoff Problem Does Not Pair, Check On The Ewelink App That The Selected Pairing Mode Is Consistent With The Blinking Frequency Of The Led On The Device:

The manual says to either push the button on the device or the wifi button on the remote for 5 seconds and it should enter pairing mode and start beeping. If the problem persists, remove it from the ewelink app and repeat the pairing process as described in my ewelink guide. Only supported devices with firmware v3+

Long Press The Button For 5 Seconds To Enter Compatible Pairing Mode.

Enter pairing mode during the first use after powering on (the bulb changes from dim to bright repeatedly); The google home app is developed by google to centrally set up, manage and control devices such as google nest, google wifi, and chromecast as well as thousands of compatible smart home products. If the device has been paired with ewelink app, reset the device is necessary by long pressing the pairing button for 5 seconds to enter bluetooth pairing mode.